Valid ACE-A1.2Dumps shared by Lead1pass for Helping Passing ACE-A1.2 Exam! Lead1pass nowoffer the newest ACE-A1.2 exam dumps, the Lead1pass ACE-A1.2 exam questions have beenupdated and answers have been corrected get the newest Lead1pass ACE-A1.2 dumpswith Test Engine here:
http://https://www.lead1pass.com/Arista/ACE-A1.2-practice-exam-dumps.html (100 Q&As Dumps, 30%OFF Special Discount: 30free )
NEW QUESTION NO: 5
What is the name of the link that connects two Arista switches together to form an MLAG domain?
A. The connector link
B. The east-west bypass link
C. The MLAG ISL (Inter-switch link)
D. The MLAG peer-link
Answer: D
Explanation/Reference:
Reference: https://eos.arista.com/mlag-basic-configuration/
NEW QUESTION NO: 6
Which of the following commands can you use to see which EOS versions are stored on the switch's flash drive (assuming a freshly booted switch)?
A. dir flash
B. bash ls /mnt/flash
C. dir
D. all of the above
Answer: D
Explanation/Reference:
Reference: http://arisq.ylb.jp/documents/bootimage
NEW QUESTION NO: 7
True or False: XMPP Management is enabled by default.
A. TRUE
B. FALSE
Answer: B
Explanation/Reference:
Reference: https://www.arista.com/en/um-eos-4172f/eos-section-2-5-session-management- commands#ww1129609
NEW QUESTION NO: 8
Arista MLAG uses which of the following protocols for inter-switch communication?
A. BGP
B. IEEE 1588
C. STP
D. None of the above
Answer: C
Explanation/Reference:
Reference: https://eos.arista.com/mlag-basic-configuration/
NEW QUESTION NO: 9
Which of the following statements is true with an Arista switch that has no configuration, but has booted with ZTP disabled?
A. You may login directly as root, but only when using SSH.
B. You can run root-level commands without a password after logging in as root.
C. You cannot issue root-level commands until you add a user with a password.
D. You may login as root, but only if you login as admin first.
Answer: C
NEW QUESTION NO: 10
Which of the following commands will show all of the hardware on an Arista switch?
A. show inventory
B. show version
C. show version detail
D. show hardware
Answer: C
Explanation/Reference:
Reference: https://eos.arista.com/how-to-store-and-view-previous-contents-of-show-tech-support/
NEW QUESTION NO: 11
What does %1 signify when writing an alias statement in CLI?
A. It means that Arista is number one.
B. %1 is a placeholder that will be replaced with token 1 when the alias is called.
C. It doesn't mean anything.
D. %1 means that the CPU is limited to 1% when the alias is called.
Answer: B
Explanation/Reference:
Reference: https://eos.arista.com/find-the-next-free-vlan-id/
NEW QUESTION NO: 12
Which command will disable Adaptive Segmentation in VMTracer?
A. Student-01(config-vmtracer-session)#autovlan disable
B. Student-01(config-vmtracer-session)#no autovlan
C. Student-01(config-vmtracer-session)#no autovlan enable
D. Adaptive Segmentation cannot be disabled in VMTracer
Answer: A
Explanation/Reference:
Reference: https://www.arista.com/assets/data/pdf/user-manual/um-eos-4172f/Chapters/um-eos-
4172f_VM%20Tracer.pdf (page 4)
NEW QUESTION NO: 13
Which of the following commands is being deprecated and will not be supported in the near future?
A. copy run start
B. none of the above
C. write memory
D. copy running-config startup-config
Answer: A
NEW QUESTION NO: 14
Which command will successfully configure Ethernet5 to be 40Gbps on an Arista 7150-52 switch?
A. An Arista 7150-52 dos not support 40Gbps
B. Since Ethernet 5 is a 10Gbps port, 40Gbps is not possible.
C. Arista(config-if-Et5)#speed forced 40gfull
D. Arista(config-if-Et5)#speed 40gfull
Answer: C
Explanation/Reference:
Reference: https://www.arista.com/zh/um-eos-4172f/eos-section-9-5-ethernet-configuration-procedures
NEW QUESTION NO: 15
Which of the following statements is false?
A. You can run CLI commands from bash with the FastCli command.
B. You can run bash commands from CLI with the bash command.
C. You can run CLI commands from CLI with the Cli command.
D. You can run CLI commands from bash with the Cli command.
Answer: C