And most of all, you will get reward by our 1y0 a28 examcollection training engine in the least time with little effort. Perhaps you have wasted a lot of time to playing computer games.
view projectIn fact, our aim is the same with you.
Latest 1Y0-A28 Free Dumps
1Y0-A28 Free Dumps Study Materials
Question 5: The network engineer would like all HTTP and HTTPS requests that travel through theNetScaler to have an HTTP header added with the source IP address for logging on the web servers.
How should the network engineer accomplish this?
A. Enable Web Logging
B. Enable the client IP option
C. Configure the TCP Parameters
D. Enable the 'Use Source IP mode'
Correct Answer: B
6. A network engineer has configured two NetScaler MPX appliances as a high availability (HA)
pair.
What can the engineer configure to prevent failover if only a single interface fails?
A. FIS
B. PBR
C. SNMP
D. VMAC
Correct Answer: A
7. Scenario: A NetScaler appliance currently has a manually configured channel containing four
interfaces;
however, the engineer has been told that the NetScaler must now only use a single interface for this
network.
The engineer removes the channel and immediately notices a decrease in network performance.
How could the engineer resolve this issue?
A. Reset the unused interfaces
B. Disable the unused interfaces
C. Enable flow control on all interfaces
D. Disable HA monitoring on the three interfaces that are no longer required
Correct Answer: B
8. Scenario: A NetScaler engineer needs to enable access to some web servers running on an
IPv6-only network. The clients connecting
the services are
on an IPv4 network. The
engineer has already enabled IPv6 on the NetScaler. What does the engineer need to do in order to
provide access to the services on the IPv6 network?
A. Create an IPv6 tunnel and a IPv4 virtual server.
B. Configure an IPv6 VLAN and bind the required interface.
C. Create a IPv4 virtual server and bind the service group to it.
D. Create an IPv6 ACL and a IPv4 virtual server and bind the ACL to the virtual server.
Correct Answer: C
9. Scenario: An engineer executes the following commands: add vlan 2 bind vlan 2 -ifnum 1 / 2 add
ns ip 10.110.4.200 255.255.255.0 bind vlan 2 -IPAddress 10.110.4.200 255.255.255.0 What type of
IP address has been added to the NetScaler?
A. VIP address
B. NSIP address
C. SNIP address
D. GSLB Site IP address
Correct Answer: C
10. Scenario: A network engineer needs to configure Citrix NetScaler to provide Access Gateway
services to VLAN 2 using interface 1 /1 only, while also using interface 1 / 2 to provide load balancing
services to VLAN 3. How could this result be achieved?
A. Disable static route advertisement.
B. Disable layer 2 mode Create 2 untagged VLANs - VLAN 2 and VLAN 3 Bind VLAN 2 to Interface 1 /1
Bind VLAN 3 to Interface 1 / 2
C. Enable Layer 3 mode Create a Channel Interface using Interface 1 /1 and 1 / 2 Create 2 VMACs Bind
a VMAC to interface 1 /1 and 1 / 2
D. Configure policy-based routing using the Interface option as a filter.
Correct Answer: B
11. Scenario: A network engineer needs to re-configure the NetScaler to utilize two new VLANs -
VLAN2 and VLAN3. VLAN2 is an untagged VLAN and VLAN3 will require a .1q compliant tag.
Interface 1 /1 is the only interface that
will be used on the NetScaler. How could the engineer configure
the NetScaler so that it can communicate with both networks?
A. Change the NSVLAN to 3 Add VLAN 2 and bind interface 1 /1 as untagged
B. Enable the Tag all VLANs option on interface 1 /1.
C. Add VLAN2 and bind interface 1 /1 as untagged Add VLAN3 and bind interface 1 /1 as tagged
D. Add a SNIP for each VLAN Enable management access on the SNIP for VLAN3
Correct Answer: C
12. Why would an engineer want to specify a TCP Profile for a specific service group?
A. To enable use of features like SSL over TCP for that specific service group.
B. To adjust the TCP settings for traffic to and from that specific service group.
C. To use a specific SNIP for traffic to the back-end servers in that service group.
D. To enable features like use source IP , TCP keep alive and TCP buffering for a specific service group.
Correct Answer: B
1y0 a28 examcollection
1y0-a28 vce
As the old saying goes people change with the times. People must constantly update their stocks of knowledge and improve their practical ability.
view project
1y0-a28 actual test
So you don't have to worry that at all and you will pass the exam for sure. Perhaps you worry about that you have difficulty in understanding our 1Y0-A28 actual test training questions.
view project 1y0 a28 download
Our products’ contents cover the entire syllabus of the exam and refer to the past years’ exam papers. Our test bank provides all the questions which may appear in the real exam and all the important information about the exam.
view project 1y0-a28 exam guide
So it is important to choose good 1Y0-A28 exam guide study materials. In fact, our aim is the same with you.
view project 1y0-a28 prep guide
You can use the version you like and which suits you most to learn our Implementing NetScaler 10 for Networking and Traffic Optimization test practice dump. The 3 versions support different equipment and using method and boost their own merits and functions.
view project
